您好!欢迎访问济南诚誉防水工程公司网站!
专注济南防水工程,防水材料,防渗工程贴心的服务,合理的收费,热诚期待您的来电!
全国咨询热线:155-5313-7958
联系我们

【 微信扫码咨询 】

155-5313-7958

济南专业防水分析填缝剂施工与季节的关系

作者:admin 浏览量:213次 来源:本站 时间:2022-12-28 15:23:06

信息摘要:

济南专业防水分析在南方夏季的气温有的高达40℃,温度过高也会使填缝剂的性能下降,所以在施工的时候大家一定要注意季节温度的变化,使填缝剂的作用达到最佳的状态。

济南专业防水http://www.tianyujian.com/介绍填缝剂在冬季不能用于室外的,因为填缝剂的施工温度在5-35℃之间。因为温度过低会导致填缝剂的性能下降,在室内使用则可以,因为北方的供暖系统比较好,虽说室外的温度在零下二三十摄氏度,但室内的温度最低也保证在零上10℃,所以填缝剂在冬季可应用于室内。因此济南专业防水建议大家在晚秋、冬季、初春的季节在北方不宜在室外进行填缝剂施工。
Jinan professional waterproof sealant presentation can not be used outdoors in the winter, because the construction temperature sealant between 5-35 ℃. Because the temperature is too low will result in sealant performance degradation

can be used indoors because of the North heating system is better, though the outdoor temperature at minus twenty or thirty degrees Celsius, but also guarantees a minimum indoor temperature at zero 10 ℃ so sealant can be used indoors

in the winter. Therefore, we recommend professional waterproof Jinan in late autumn, winter, early spring season in the North should not be performed in the outdoor construction sealant.

济南专业防水分析在南方夏季的气温有的高达40℃,温度过高也会使填缝剂的性能下降,所以在施工的时候大家一定要注意季节温度的变化,使填缝剂的作用达到最佳的状态。
Jinan professional waterproofing analysis in some southern summer temperatures as high as 40 ℃, the temperature was too high to make the sealant performance degradation, so when we must pay attention to the construction of seasonal

temperature changes, so that the role of sealant to achieve the most good condition.

济南专业防水http://www.tianyujian.com/建议大家使用时清除底材表面污物、油脂,并用少许水雾喷湿待填充部位,在0℃~40℃温度范围内施工使用,若在寒冷季节施工,为保证使用效果,建议将罐体放在30℃环境中预热,施工前上下用力摇动一分钟以上,施工时请将罐体始终保持倒置状态。每罐施工完毕,请用专用清洗剂清洗胶枪螺纹部分,每次连续施工完毕,请用专用清洗剂清洗整个胶枪管,以免固化堵塞。修补和切割请在泡沫完全固化成型后进行,值得注意的是,切去泡沫的表皮会降低泡沫强度并降低泡沫的密封防水效果。
Jinan professional waterproof suggest that you remove the use of the substrate surface dirt, grease, and with a little mist wet the parts to be filled in the temperature range of 0 ℃ ~ 40 ℃ construction use, if the construction in the

cold season, to ensure the results, it is recommended the tank on the 30 ℃ environment preheated before construction shake down more than one minute, the construction of the tank please remain inverted state. Each tank construction is completed, wash with a special cleaning agent glue gun threaded portion, each successive construction is completed, clean the entire plastic barrel with a special cleaning agent, in order to avoid clogging cured. Repair and cutting in the fully cured foam after molding carried out, it is worth noting that cut skin foam reduces the strength of the foam and reducing the sealing waterproof foam.